大发平台游戏

  • <tr id='tYTfAe'><strong id='tYTfAe'></strong><small id='tYTfAe'></small><button id='tYTfAe'></button><li id='tYTfAe'><noscript id='tYTfAe'><big id='tYTfAe'></big><dt id='tYTfAe'></dt></noscript></li></tr><ol id='tYTfAe'><option id='tYTfAe'><table id='tYTfAe'><blockquote id='tYTfAe'><tbody id='tYTfAe'></tbody></blockquote></table></option></ol><u id='tYTfAe'></u><kbd id='tYTfAe'><kbd id='tYTfAe'></kbd></kbd>

    <code id='tYTfAe'><strong id='tYTfAe'></strong></code>

    <fieldset id='tYTfAe'></fieldset>
          <span id='tYTfAe'></span>

              <ins id='tYTfAe'></ins>
              <acronym id='tYTfAe'><em id='tYTfAe'></em><td id='tYTfAe'><div id='tYTfAe'></div></td></acronym><address id='tYTfAe'><big id='tYTfAe'><big id='tYTfAe'></big><legend id='tYTfAe'></legend></big></address>

              <i id='tYTfAe'><div id='tYTfAe'><ins id='tYTfAe'></ins></div></i>
              <i id='tYTfAe'></i>
            1. <dl id='tYTfAe'></dl>
              1. <blockquote id='tYTfAe'><q id='tYTfAe'><noscript id='tYTfAe'></noscript><dt id='tYTfAe'></dt></q></blockquote><noframes id='tYTfAe'><i id='tYTfAe'></i>

                HN ELECTRONIC

                专业从事电磁式蜂鸣器、压电式蜂鸣器生产及研发

                MLT-4020H

                MLT-4020H

                MLT-4020H

                MLT-4020H

                MLT-4020H

                产品说明

                Specification for Electro-Magnetic Buzzer
                     (SMD Type)

                 

                Page 2 of 6

                Des.

                Chk.

                Model No.:

                MLT-4020H

                Part No.

                 

                 

                 

                  
                1. Technical Parameter

                Measuring condition
                       Part shall be measured under a condition (Temperature: 5~35℃, Humidity: 45%~85%R.H., Atmospheric pressure: 860 ~1060hPa) unless the standard condition (Temperature: 25±3℃, Humidity: 60±10%R.H. Atmospheric pressure: 860 ~1060hPa) is regulated to measure.

                1

                Rated Voltage

                3.0Vo-p

                2

                Operating Voltage

                2.0~5.0Vo-p

                3

                Rated Current

                Max.100mA at 4000Hz 50% duty Square Ware 3.0Vo-P

                4

                Sound Output at 10cm

                Min. 75Db,at 4000Hz 50% duty Square Ware 3.0Vo-p

                5

                Coil Resistance

                12±3Ω

                6

                Resonant Frequency

                4000Hz

                7

                Operating Temperature

                -20℃~+70℃

                8

                Store Temperature

                -40℃~+85℃

                9

                Net Weight

                Approx 0.1g

                10

                RoHS

                Yes

                1. Dimensions

                Unit: mm

                 

                *Unit: mm; Tolerance: ±0.3mm Except Specified
                     *Housing Material: Black LCP
                     *Terminal plate: 3 soldering pads, tin Plating Brass

                1. Electrical And Acoustical Measuring Condition

                Recommended Driving Circuit
                      
                     Resonant frequency, 1/2 duty cycle. Square wave.
                     Signal amplitude should be large enough tosaturate
                     the transistor.

                Recommended Setting
                      

                1. Frequency Response

                 
                       3.6Vo-p 50% duty Square wave,10cm

                1. Surface mounting condition

                5.1 Reflow soldering
                       Recommendable reflow soldering condition is as follows.
                        
                       Note: (1) In automated mounting of the SMD sound transducers on PCB, any bending, expanding
                       and pulling forces or shocks against the SMD sound transducers shall be kept minimum
                       to prevent them from electrical failures and mechanical damages of the devices.
                       (2) In the reflow soldering, too high soldering temperatures and too large temperature
                       Gradient such as rapid heating or cooling may cause electrical failures and mechanical
                       damages of the devices.

                1. Reliability Test

                After any following tests the part shall meet specifications without any degradation in
                       appearance and performance except SPL. SPL shall not deviate more than -10 dB
                       from the initial value

                  1. Ordinary Temperature Life Test

                The part shall be subjected to 96 hours at 25±10℃. Input rated voltage
                       Resonant frequency, 1/2 duty Square wave.
                       6.2 High Temperature Test
                       The part shall be capable of with standing a storage temperature of +80℃ for 96 hours.
                       6.3 Low Temperature Test 
                       The part shall be capable of with standing a storage temperature of -30℃ for 96 hours.

                  1. Humidity Test

                Temperature:+40℃±3℃   Relative Humidity:90%~95% Duration: 48 hours
                       and expose to room temperature for 6 hours

                  1. Temperature Shock Test

                Temperature:60℃ /1hour→ 25℃/3hours→-20℃/1hour→ 25℃/3hours (1cycle)
                       Total cycle: 10 cycles

                  1. Drop Test

                Standard Packaging From 75cm(Drop on hard wood or board of 5cm thick,
                       three sides, six plain.)

                  1. Vibration Test

                Vibration:1000cycles /min. Amplitude:1.5mm, Duration: 1 hour in each 3 axes

                  1. Reflow Test

                Use recommendable reflow soldering condition (as shown in 5.1)
                       (1) No abnormality should be found after reflow
                       (2) Good soldering to meet soldering requirements

                 

                Note:
                       As this product is not protected from foreign material entering, please make sure that any foreign materials (e.g. magnetic powder, washing solvent, flux, corrosive gas) do not enter this product in your production processes. The functional degradation (e.g. SPL down) may occur if foreign material enter it.

                1. Packing